Моделювання процесу розпилення рідини у обладнанні для модифікації поверхонь складної форми
Вантажиться...
Дата
2014
Автори
Горященко, К.Л.
Карван, С.А.
Назва журналу
Номер ISSN
Назва тому
Видавець
Хмельницький національний університет
Анотація
В статті розглядається високодисперсне розпилення за умови низького тиску та осаджування краплин з
мінімальними втратами через випаровування та обладнання для його здійснення. Розроблено процес модифікації
поверхонь складних форм за допомогою розпилення рідини у запропонованому обладнанні. Проведено моделювання
процесу розпилення рідини з урахування того, що обладнання оснащено вакуумною камерою та спеціальною
форсункою для розпилення. Розроблено модель форсункирозпилювача
в ПП SolidWorks. Проведено аналіз потоку
рідини, що розпилюється, в ПП FloWorks з урахуванням пониженого тиску в камері пристрою. Показано напрями
потоків рідини при розпиленні в вакуумі. Надано рекомендації щодо розташування об’єктів в камері.
Моделюванням підтверджено можливість розпилення рідини на поверхню мінералів, причому визначено
швидкість руху рідини, що сягає 12,108 м/с, а також визначено, що потік рідини ударяє в центрі камери, і лише
потім розпилюється в сторони.
The article considers the superfine spray at the low pressure and deposition of droplets with minimal loss through evaporation and equipment for its implementation. A surface modification process of the complicated shapes by spraying the liquid was elaborated on the basis of the proposed equipment. The simulation process of spraying the liquid was realized and took into account the fact that the equipment is equipped with a vacuum chamber and a special nozzle to spray. The model of spray nozzles is elaborated in SolidWorks. The analysis of fluid flow which is sprayed is carried out in FloWorksz considering the reduced pressure in the chamber of the device. The flow of liquid at the spraying in a vacuum was shown. The recommendations on the location of objects in the chamber are given. The modelling confirms the possibility of spraying the liquid on the surface of minerals and result in the determination of the velocity of the liquid which reaches 12.108 m/s. Also it is shown the flow of liquid hits in the center of the chamber and then sprays in the sides.
The article considers the superfine spray at the low pressure and deposition of droplets with minimal loss through evaporation and equipment for its implementation. A surface modification process of the complicated shapes by spraying the liquid was elaborated on the basis of the proposed equipment. The simulation process of spraying the liquid was realized and took into account the fact that the equipment is equipped with a vacuum chamber and a special nozzle to spray. The model of spray nozzles is elaborated in SolidWorks. The analysis of fluid flow which is sprayed is carried out in FloWorksz considering the reduced pressure in the chamber of the device. The flow of liquid at the spraying in a vacuum was shown. The recommendations on the location of objects in the chamber are given. The modelling confirms the possibility of spraying the liquid on the surface of minerals and result in the determination of the velocity of the liquid which reaches 12.108 m/s. Also it is shown the flow of liquid hits in the center of the chamber and then sprays in the sides.
Опис
Ключові слова
модель, розпилення, обладнання для модифікації, model, spray equipment modifications
Бібліографічний опис
Горященко, С.Л. Моделювання процесу розпилення рідини у обладнанні для модифікації поверхонь складної форми [Текст] / С. Л. Горященко, С. А. Карван // Вісник Хмельницького національного університету. Технічні науки. – 2014. – №3. – С. 159-163.