Моделювання відхилення профілю повздовжнього перерізу циліндричної поверхні деталі внаслідок пружних відтискань в технологічній системі при токарній обробці
Вантажиться...
Файли
Дата
2013
Автори
Соколан, К.С.
Sokolan, K.S.
Кокорев, Д.К.
Kokorev, D.K.
Назва журналу
Номер ISSN
Назва тому
Видавець
Хмельницький національний університет
Анотація
В статті доводиться необхідність моделювання відхилення профілю повздовжнього перерізу при
токарній обробці для циліндричних поверхонь, таких як вали та ступінчасті вали. Проаналізовано в деталях
фізичні процеси, що призводять до відхилення профілю повздовжнього перерізу при обточуванні циліндричних
поверхонь. Показано математичні методи розрахунку податливості балок для двух схем навантаження балки, які
імітують вал, що обточується у верстаті. Вказано методи розрахунку податливості верстата відповідно до
певних схем обробки. В цій статті пояснюється головна логіка: як застосовувати наведені вище методи коректно
для того, щоб розрахувати податливість технологічної системи, при їх реалізації в прикладній програмі. Щодо
моделювання похибки, автор представляє програмний додаток для моделювання, оснований на “Cистемі
розрахунку режимів різання”. Автор вказує принципи проектування деяких екранів інтерфейсу користувача в
додатку і відмічає трюки програмування – як можна упередити користувача від вводу суперечливих даних і
заплутатись при користуванні додатком. Також описано як тлумачити результати програми і дано приклад
того, як може виглядати реальнийшар матеріалу, утворений похибками пружних відтискань.
This article proofs the necessity of modelling the deviation from true longitudinal section profile when cutting a radial surfaces such as shafts and multidiameter shafts. Were described in depth the physical processes, those lead to the deviation from true longitudinal section profile when cutting radial surfaces. Were shown the math methods of calculation the suppleness of beams for the two beam-loading conditions, those imitate the shaft while cutting. Were pointed the methods of calculating the compliance of a turning machine accordingly to some certain cut-map. This article explains the main logic of how to use correctly the methods those mentioned above to calculate the slack of a technological system while implementing them into an application. As of deviation modelling, the author introduces a modelling application, which is based on the “Cutting conditions calculation system”. The author points the principles of designing the user interface of some screens in the application and notices developers’ tricks of how to both avoid a user to enter contradicting data and get becoming confused, while using the application. It is also outlined of how to interpret the results of the application and given an example of what the real deviation layer might look like.
This article proofs the necessity of modelling the deviation from true longitudinal section profile when cutting a radial surfaces such as shafts and multidiameter shafts. Were described in depth the physical processes, those lead to the deviation from true longitudinal section profile when cutting radial surfaces. Were shown the math methods of calculation the suppleness of beams for the two beam-loading conditions, those imitate the shaft while cutting. Were pointed the methods of calculating the compliance of a turning machine accordingly to some certain cut-map. This article explains the main logic of how to use correctly the methods those mentioned above to calculate the slack of a technological system while implementing them into an application. As of deviation modelling, the author introduces a modelling application, which is based on the “Cutting conditions calculation system”. The author points the principles of designing the user interface of some screens in the application and notices developers’ tricks of how to both avoid a user to enter contradicting data and get becoming confused, while using the application. It is also outlined of how to interpret the results of the application and given an example of what the real deviation layer might look like.
Опис
Ключові слова
різання металів, різець, оброблювана поверхня, токарна обробка, токарний універсальний верстат, технологічна система, жорсткість, податливість технологічної системи, податливість заготовки, похибка обробки, metalcutting, cutter, processing surface, turning, turning machine, technological system, stiffness, slack, suppleness, working error
Бібліографічний опис
Соколан, К. С. Моделювання відхилення профілю повздовжнього перерізу циліндричної поверхні деталі внаслідок пружних відтискань в технологічній системі при токарній обробці [Текст] / К. С. Соколан, Д. К. Кокорев // Вісник Хмельницького національного університету. Технічні науки. – 2013. – № 5. – С. 78-86.