Аналіз технології виготовлення виливків важелів підйомника
Вантажиться...
Файли
Дата
2013
Автори
Дробот, О.С.
Волинський, Б.С.
Drobot, O.
Volynski, B.
Назва журналу
Номер ISSN
Назва тому
Видавець
Хмельницький національний університет
Анотація
В статті наведено результати аналізу технології виготовлення виливків важеля підйомника з метою
вибору раціонального способу, який забезпечить якість виливків у відповідності до технічних умов на їх
виготовлення. Виливки складної форми (типу важелів) рекомендовано виготовляти способом лиття з
використанням плавких моделей. При одержанні виливків методом лиття з використанням плавких моделей для
попередження утворення зневуглецьованого шару формовку керамічної оболонки потрібно проводити в
термостаті з використанням певної кількості карбюрізатора (деревинного вугілля) для створення
відновлювальної атмосфери в керамічній оболонці і біля неї під час кристалізації та охолодження виливка.При
проведенні нормалізаційного відпалу під час нагрівання виливок для попередження зневуглецювання
використовувати захисні середовища.
In the article are presented the results of analysis of technology of making of foundings of lever of lift are resulted with the purpose of choice of rational method, which will provide quality of foundinqs in accordance TTS on their making. The irregular shape halfblank castings of the heaver type are to be produced by means of casting with fusible components application. While obtaining the halfblank castings by means of casting with fusible components application, to prevent the decarbonized layer formation, one should carry out the ceramic cover molding in the thermostat with a certain amount of carburizing material (wood coal) application; it is to create the restorable atmosphere in the ceramic cover and by its side in time of crystallization and halfblank casting cooling. While holding the normalizing bakeout during halfblank castings heating one is to use shielding medium for decarbonization prevention. The cooling medium at И20А hardening conditions is reasonably to be changed for watersoluble polymer solutions that enable the possibility of optimal cooling rate control both in pearlite and martensite temperatures range of supercooled austenite decomposition.
In the article are presented the results of analysis of technology of making of foundings of lever of lift are resulted with the purpose of choice of rational method, which will provide quality of foundinqs in accordance TTS on their making. The irregular shape halfblank castings of the heaver type are to be produced by means of casting with fusible components application. While obtaining the halfblank castings by means of casting with fusible components application, to prevent the decarbonized layer formation, one should carry out the ceramic cover molding in the thermostat with a certain amount of carburizing material (wood coal) application; it is to create the restorable atmosphere in the ceramic cover and by its side in time of crystallization and halfblank casting cooling. While holding the normalizing bakeout during halfblank castings heating one is to use shielding medium for decarbonization prevention. The cooling medium at И20А hardening conditions is reasonably to be changed for watersoluble polymer solutions that enable the possibility of optimal cooling rate control both in pearlite and martensite temperatures range of supercooled austenite decomposition.
Опис
Ключові слова
технологія, лиття, виливок, модель, термічна обробка, technique, cast, casting, heat-treating
Бібліографічний опис
Дробот, О. С. Аналіз технології виготовлення виливків важелів підйомника [Текст] / О. С. Дробот, Б. С. Волинський // Вісник Хмельницького національного університету. Технічні науки. – 2013. – № 2. – С. 45-48.