Кафедра інженерії програмного забезпечення
Постійне посилання зібрання
Переглянути
Перегляд Кафедра інженерії програмного забезпечення за Автор "Goroshko, A."
Зараз показуємо 1 - 3 з 3
Результатів на сторінці
Налаштування сортування
Документ Design methods for reduction of forced vibrations of horizontal rotary machines(2021) Drach, I.; Goroshko, A.На примере стиральных машин в рамках линейной теории колебаний исследована динамика горизонтальных роторных машин барабанного типа и сформулированы основные требования к их компоновке для снижения виброактивности. В матричной форме составлены математические уравнения колебаний многосвязной системы бак-барабан на упругих подвесах для основных типов машин и отжимных центрифуг с горизонтальной осью вращения. Задачи решены в линейной постановке на основании уравнения Лагранжа II рода. Точность и адекватность математической модели проверялась непосредственно на натурном объекте путем измерения шума, вибраций, усилий в опорах и распределения напряжений в отдельных элементах и узлах машины во всем диапазоне частот вращения барабана. Исследования характера колебаний системы в зависимости от изменения положения и точек крепления упругих и демпфирующих элементов проводились с помощью имитационного моделирования в среде Simulink. В результате исследований были экспериментально подтверждены основные требования к компоновке горизонтальных роторных машин барабанного типа: центр масс бака должен лежать на оси вращения барабана; ось вращения барабана должна являться главной центральной осью инерции бака; центр масс бака должен совпадать с центром масс загруженного барабана; центр жесткости системы упругих опор должен совпадать с центром тяжести бака, а главные оси жесткости – с главными центральными осями инерции бака; главные оси постоянных вязкого трения должны совпадать с главными центральными осями инерции бака.Документ Design Principles of Horizontal Drum Machines with Low Vibration(2021) Drach, I.; Goroshko, A.; Dwornicka, R.Using the example of washing machines using the linear theory of vibrations, the dynamics of horizontal rotary drum machines is investigated and the basic requirements for their layout are formulated to reduce vibration activity. The mathematical equations of vibrations of the multiply connected system tub-drum on elastic suspensions are compiled for main types of washing machines and centrifuges with horizontal axis of rotation. The problem is solved in a linear setting based on the Lagrange equation of the second kind. The accuracy and adequacy of the mathematical model was tested directly on a full-scale object by measuring noise, vibrations, support forces and stress distribution in individual elements and units of the washing machine in the entire range of drum rotation frequencies. Investigations of the nature of system vibrations depending on changes in the position and attachment points of elastic and damping elements were carried out using simulation in the Simulink environment. As a result of the research, the basic requirements for the layout of horizontal rotary drum machines were experimentally confirmed. Experimental verification was carried out to confirm the results obtained. It has been experimentally proven that the improvement of the experimental setup to reduce its vibration activity increases the efficiency of using direct-acting liquid autobalancers.Документ Fluid Behavior in an Auto-balancing Unit Without External Damping(2021) Drach, I.; Goroshko, A.This article describes mathematical models of stationary motion in rigid supports of a rigid rotor with a cylindrical chamber partially filled with fluid. It is considered limited from the above chamber, which is located eccentrically and symmetrically on the shaft. In each case, based on integrating the liquid equilibrium differential equations, the pressure distribution laws in the fluid and specific shapes of equal pressure surfaces are defined. Considered cases simulate fluid behavior in an auto-balancer without considering external damping. It is investigated that the fluid is symmetrical about the axis of rotation of the system. Simultaneously, its bulk is concentrated by eccentricity (with the eccentric arrangement of the chamber). The constructed models’ analysis shows the impracticability of automatically balancing the rigid rotor with fluid in the rigid supports. The experimental results confirm the assertion. These results are obtained using dynamic photography, which is realized on an up-to-date computer and video equipment.