Вплив термператури гартування на контактну витривалість сталі х12 при терті кочення
Вантажиться...
Дата
2018
Автори
Каплун, П.В.
Гончар, В.А.
Паршенко, А.В.
Kaplun, P.V.
Gonchar, V.A.
Parshenko, A.V.
Назва журналу
Номер ISSN
Назва тому
Видавець
Хмельницький національний університет
Анотація
Наведені результати експериментальних досліджень впливу температури гартування сталі Х12 на її
твердість, вміст залишкового аустеніту в структурі матеріалу та контактну витривалість при терті кочення в мастилі
І-20. Показано, що з підвищенням температури гартування сталі збільшується кількість залишкового аустеніту в
структурі матеріалу та зменшується його твердість. Встановлена нелінійна залежність між вмістом залишкового
аустеніту в сталі та її контактною витривалістю при терті кочення. Показано,що в процесі кочення частина
залишкового аустеніту перетворюється в мартенсит під дією пластичної деформації. В результаті чого відбувається
підвищення твердості поверхні. Визначено оптимальне значення вмісту залишкового аустеніту30 % в структурі сталі
Х12, при якому досягається її максимальна контактна витривалість.
The results of experimental studies of the influence of the tempering temperature of X12 steel on its hardness, the content of residual austenite in the structure of the material, and the contact durability of the rolling gravity in the lubricant and-20. It is shown that as the temperature of the quenching of steel increases, the amount of residual austenite increases in the structure of the material, which increases with a tempering temperature and reaches 90% at a temperature of 1120 ° C. This leads, accordingly, to a decrease in the microhardness of the material from H100 = 8520 to 5280 MPa. Installed nonlinear dependence between the content of residual austenite in the steel and its contact endurance when rolling friction. It is shown that in the process of rolling a portion of the residual austenite is transformed into martensite under the action of plastic deformation. Resulting in increase of surface hardness and durability of steel. The influence of the martensitic transformation to increase the hardness and durability in the rolling friction can be estimated using the ratio of the completeness of the martensitic transformation Km, which for X12 steel after quenching is in the range of 0.28 – 0.3 mm. In the process of martensitic transformation there is a partial absorption of deformation energy, which, together with the increase of the hardness of the deformed layer, helps to increase the durability of steel. The optimal value of retained austenite content of 30% in the structure of X12 steel at which the maximum contact her endurance.
The results of experimental studies of the influence of the tempering temperature of X12 steel on its hardness, the content of residual austenite in the structure of the material, and the contact durability of the rolling gravity in the lubricant and-20. It is shown that as the temperature of the quenching of steel increases, the amount of residual austenite increases in the structure of the material, which increases with a tempering temperature and reaches 90% at a temperature of 1120 ° C. This leads, accordingly, to a decrease in the microhardness of the material from H100 = 8520 to 5280 MPa. Installed nonlinear dependence between the content of residual austenite in the steel and its contact endurance when rolling friction. It is shown that in the process of rolling a portion of the residual austenite is transformed into martensite under the action of plastic deformation. Resulting in increase of surface hardness and durability of steel. The influence of the martensitic transformation to increase the hardness and durability in the rolling friction can be estimated using the ratio of the completeness of the martensitic transformation Km, which for X12 steel after quenching is in the range of 0.28 – 0.3 mm. In the process of martensitic transformation there is a partial absorption of deformation energy, which, together with the increase of the hardness of the deformed layer, helps to increase the durability of steel. The optimal value of retained austenite content of 30% in the structure of X12 steel at which the maximum contact her endurance.
Опис
Ключові слова
контактна витривалість, гартування, залишковий аустеніт, твердість, сontact endurance, hardening, residual austenite, hardness
Бібліографічний опис
Гончар, В.А. Вплив термператури гартування на контактну витривалість сталі Х12 при терті кочення [Текст] / В. А. Гончар, П. В. Каплун, А. В. Паршенко // Проблеми трибології. – 2018. – №4. – C. 80-84.