Зносостійкість конструкційних сталей при азотуванні в циклічно-комутованому розряді
Вантажиться...
Дата
2024
Автори
Назва журналу
Номер ISSN
Назва тому
Видавець
Хмельницький національний університет
Анотація
Фізико-технічні процеси обробки поверхонь металів з використанням в якості інтенсифікатора електричного розряду в газовому середовищі відносяться до найменш енергоємних та універсальних за призначенням і
використанням. Проте широкому впровадженню процесів БАТР перешкоджає відсутність загальних теоретичних основ, за яких стали б можливими оптимізація, ефективне керування та проектування технологічних процесів.
Метою досліджень є розвиток теоретичних і розробка практичних основ підвищення зносостійкості металів безводневим азотуванням в циклічнокомутованому розряді, а також встановлення основних закономірностей та умов азотування довгомірних отворів для забезпечення їх зносостійкості.
Аналіз джерел вказує на те, що всі відомі моделі процесу в теоретичному плані в значній мірі носять гіпотетичний характер, оскільки в повній мірі не підтверджуються експериментально. Цілий ряд варіантів реалізації вакуумнодифузійних газорозрядних технологій взагалі не можуть бути пояснені на основі згаданих моделей. При їх формуванні практично не використовується аналітичний апарат, ігнорується необхідність пояснення деяких явищ, які принципово впливають на прийнятність теорії, відсутні критерії, а звідси і
методи керування процесом з метою досягнення запланованих та необхідних для експлуатації показників модифікації. Наявність об’ємної бази технологічних даних, яка не має під собою узагальнюючої теорії, не тільки не сприяє оптимізації технологічного процесу, але навпаки часто призводить до протилежних наслідків, оскільки дані для однотипних умов нерідко вступають в протиріччя між собою.
В роботі розвинуто положення теорії дифузійних газорозрядних процесів модифікації поверхні металів, які базуються на пріоритеті енергетичних підходів. З таких позицій теоретичні основи досліджуваних технологій не розглядались жодним з попередніх дослідників, але якраз подібні підходи відкривають абсолютно нові можливості розкриття тонкого механізму явищ, котрі мають місце при реалізації процесів даного типу, і далі – розробки практичних аспектів використання технології.
Концептуальною основою теоретичних підходів, які використані в роботі є енергетична модель групи досліджуваних процесів, суть якої полягає в тому, що в певних конкретних умовах у першу чергу реалізуються ті з елементарних субпроцесів, котрі енергетично найбільш вигідні та ймовірні з огляду на рівні енергії чинників, що стимулюють ці субпроцеси. Для реалізації вказаних положень послідовно досліджено формування енергетичних характеристик стимуляторів процесу, насамперед, елементів потоків, які взаємодіють з поверхнею. При цьому за основу прийнято фактор енергетичного впливу потоків на поверхню як з позицій кількості, так і енергетичних рівнів часток.
Саме комбінація цих характеристик має вирішальне значення для формування характеристик основних елементарних процесів.
Значний науковий інтерес з перспективою широкого практичного використання становить задача застосування живлення, відмінного від безперервного. Ці питання теоретично теж ніким не досліджувались. В той же час реально всі процеси вакуумно-дифузійної газорозрядної модифікації поверхні металів проходять в нестаціонарних електричних полях, оскільки забезпечити живлення абсолютно постійним струмом практично неможливо.
Зміна характеристик поля призводить до першочергового проходження одного з декількох конкуруючих субпроцесів, які забезпечують або утворення дифундидів на поверхні, або їх розпорошення, або дифузію азоту в глибину поверхневого шару. Саме з допомогою керованої форми електричних показників поля в розрядній камері можлива нейтралізація в необхідній мірі запірного ефекту утворення на поверхні дифундидів, що дозволить не тільки підвищити ефективність модифікації, але й скеровано забезпечувати необхідні її кінцеві результати, в тому числі і структуру поверхневого модифікованого шару.
Виходячи з концепції енергетичної моделі, теоретично обгрунтовано та проведено експериментальну перевірку впливу форми керуючого сигналу на ефективність процесів модифікації, оскільки цей фактор суттєво впливає на трибологічні характеристики азотованих шарів.
Трибологічні дослідження проводились на основі положень фізикохімічної механіки матеріалів, розроблених Г.В. Карпенко, Г.О. Прейсом, А. Евансом і К. Пріс, Ф. Хеммітом, а також теорії структурного пристосування
поверхневих азотованих шарів при терті Костецького Б. І. та механо-хімічної моделі процесу тертя і зношування Шевелі В. В. і Олександренка В. П. В результаті реалізації досліджень отримано, на положеннях фізики газорозрядних процесів, принципово нові наукові результати, котрі пов’язані з вирішенням практичних задач. Узагальнені теоретичні положення енергетичної моделі процесів досліджуваного типу дозволяють сформувати систему аналітичних критеріїв, розробити принципово нові методики проектування та
автоматизованого управління технологічними процесами цієї групи. Викладені вище основні концептуальні підходи в порівнянні з відомими публікаціями кваліфікують їх як принципово нові у світовій науковій практиці.
Теоретичні положення, розроблені в роботі, передбачається використати не тільки в практиці застосування технологічних процесів досліджуваного типу, але у підготовці фахівців при викладанні навчальних курсів принципово нових напрямків теорії та практики газорозрядних процесів обробки поверхні металів. З теоретичних результатів, котрі одержані в ході виконання досліджень, випливають абсолютно нові, інноваційні методики та алгоритми керування процесом.
Враховуючи багатогалузевий характер можливого використання означеної технології модифікації, теоретичні дослідження процесу особливо актуальні для багатьох галузей промисловості України. Наявність напрацювань у вибраному напрямку направлено на подальше зростання виробництва в Україні високотехнологічного устаткування та продукції.
Наукова новизна отриманих результатів полягає в наступному:
- Вперше запропоновано ввести критерій концентрації поля, що дозволило розв’язати аналітичну задачу встановлення взаємозв’язків геометрії поверхні та параметрів електричного поля, а також їх вплив на зносостійкість азотованих в циклічно-комутованому розряді поверхонь сталей.
- Вперше отримано аналітичний вираз для визначення середньої швидкості електронів в тліючому розряді, для цього використано модель базової швидкості, яку має електрон, що пролетів без зіткнень від катода до
певної точки області катодного падіння.
- Виявлено явище-ефект релаксаційних процесів в приповерхневих шарах сталей, азотованих в циклічно-комутованому розряді. Релаксують структури та напруження, що утворюються в поверхневих шарах цих матеріалів під дією тиску і температури в зоні тертя.
- Встановлено, що підвищення майже в 2 рази зносостійкості поверхонь довгомірних отворів сталевих деталей, азотованих в циклічно-комутованому розряді, зумовлено ефектом накачування іонів азоту в отвір і, як наслідок, рівномірного розподілу поверхневої мікротвердості по усій довжині.
- Отримала подальший розвиток методологія підвищення зносостійкості сталей безводневим азотуванням в циклічно-комутованому розряді, що є наслідком зміни співвідношення структурних складових фазового складу поверхневого модифікованого шару.
- Підвищення зносостійкості сталевих деталей вузлів тертя в 1,35…1,75 разів азотуванням в циклічно-комутованому розряді зумовлена тим, що періодична зміна полярності електродів камери сприяє процесам очистки поверхні від адсорбційного шару, що позитивно впливає на характер насичення поверхні азотом (градієнт зміни мікротвердості по глибині азотованого шару знижується від 1,7 до 3,5 рази).
Практичне значення одержаних результатів:
- Застосування запропонованого комплексу апаратури в якості ключа, при азотуванні в тліючому розряді з нестаціонарним живлення, дозволило реалізувати весь спектр робочих струмів та напруг, що відкриває шлях до практичного використання нестаціонарного розряду для модифікації поверхонь металевих сплавів та підвищення іх зносостійкості.
- Дослідження зносостійкості зразків в режимі сухого тертя забезпечує суттєво більшу продуктивність проведення експериментів. На відміну, від експериментів з граничним тертям, сухе тертя може застосовуватись для різних сталей, з однаковим значенням тиску в зоні контакту, що дозволяє полегшити
порівнювання результатів та сприяє об’єктивності висновків щодо ефективності різних процесів модифікації поверхні. За результатами проведених експериментальних досліджень таким компромісним тиском може
бути значення в 16 МПа. Встановлений ефект релаксаційних перетворень поверхонь тертя, які були азотовані в циклічно-комутованому розряді, вимагає рекомендувати для забезпечення адекватності та співставлення результатів проводити дослідження зносостійкості таких поверхонь протягом однієї безперервної зміни.
- При БАТР з живленням струмом промислової частоти здешевлюється установка для реалізації процесу. (патент України № 112983). Розроблена технологія впроваджена для зміцнення зубчастих обойм, зубчастих втулок, валшестерень, коліс зубчастих на ТОВ «МАГМА», м. Маріуполь, що показала збільшення зносостійкості від 1,35 до 1,85 порівняно із зміцненням струмом високої частоти.
- Можливість комутації форми імпульсів, зміни їх полярності привела до розробки цілої низки способів і технологій азотування (патенти України, № 113576, №115969, №112984, №112613 та №111949) направлених на підвищення зносостійкості виробів з металів: перехідних втулок з внутрішніми і зовнішніми
конічними різьбами; шнеків термопласт-автоматів; впроваджено на ТОВ «Завод бурового обладнання», м. Коростень, на ПП «Юркон», на Хмельницькій маслосирбазі і об`єднанні «Хмельпиво».
Результати теоретичних та експериментальних досліджень роботи використовуються в навчальному процесі ХНУ на кафедрі галузевого машинобудування та агроінженерії при викладанні дисциплін «Прогресивні
технології зміцнення», «Трактори і автомобілі».
Physico-technical processes of processing metal surfaces with the use of electric discharge as an intensifier in a gas medium are among the least energyintensive and universal in terms of purpose and use. However, the lack of general theoretical foundations, which would enable optimization, effective management and design of technological processes, hinders the widespread implementation of BATR processes. The purpose of the research is the development of theoretical and practical foundations of increasing the wear resistance of metals by anhydrous nitriding in a cyclically switched discharge, as well as establishing the basic laws and conditions of nitriding of long holes to ensure their wear resistance. The analysis of sources indicates that all known models of the process are theoretically largely hypothetical, as they are not fully confirmed experimentally. A number of options for the implementation of vacuum-diffusion gas-ischarge technologies cannot be explained at all on the basis of the mentioned models. Analytical apparatus is practically not used in their formation, the need to explain some phenomena that fundamentally affect the acceptability of the theory is ignored, there are no criteria, and hence the methods of managing the process in order to achieve the planned and necessary for operation modification indicators. The presence of a voluminous database of technological data, which does not have a generalizing theory, not only does not contribute to the optimization of the technological process, but on the contrary often leads to the opposite consequences, since data for the same type of conditions often contradict each other. The paper develops the position of the theory of diffusion gas-discharge processes of metal surface modification, which are based on the priority of energy approaches. From such positions, the theoretical foundations of the researched technologies were not considered by any of the previous researchers, but precisely such approaches open completely new possibilities for revealing the subtle mechanism of phenomena that take place during the implementation of processes of this type, and further - the development of practical aspects of the use of technology. The conceptual basis of the theoretical approaches used in the work is the energy model of the group of researched processes, the essence of which is that under certain specific conditions those of the elementary subprocesses are implemented first of all, which are energetically most advantageous and probable in view of the energy levels of the factors that stimulate these subprocesses. To implement these provisions, the formation of energy characteristics of process stimulators, primarily of flow elements that interact with the surface, has been consistently studied. At the same time, the factor of energy impact of flows on the surface is taken as a basis, both in terms of the number and energy levels of particles. It is the combination of these characteristics that is of decisive importance for the formation of the characteristics of the main elementary processes. Significant scientific interest with the prospect of wide practical use is the problem of applying power other than continuous. These issues have also not been studied theoretically by anyone. At the same time, in reality, all processes of vacuumdiffusion gas-discharge modification of the surface of metals take place in nonstationary electric fields, since it is practically impossible to provide power with an absolutely constant current. A change in the characteristics of the field leads to the priority passage of one of several competing sub-processes, which ensure either the formation of diffuses on the surface, or their dispersion, or the diffusion of nitrogen into the depth of the surface layer. It is with the help of the controlled form of the electric field indicators in the discharge chamber that it is possible to neutralize to the required extent the blocking effect of the formation of diffundides on the surface, which will allow not only to increase the efficiency of the modification, but also to provide the necessary final results, including the structure of the surface modified layer. Based on the concept of the energy model, the influence of the shape of the control signal on the efficiency of the modification processes was theoretically substantiated and experimentally verified, since this factor significantly affects the tribological characteristics of nitrided layers. Tribological studies were carried out on the basis of the provisions of physicochemical mechanics of materials developed by G. V. Karpenko, G. O. Preis, A. Evans and K. Preis, F. Hammit, as well as the theory of structural adjustment of surface nitrided layers during friction by B. I. Kostecki and the mechano-chemical model of the friction and wear process by V. V. Sheveli and V. P. Oleksandrenko. As a result of the research, fundamentally new scientific results related to the solution of practical problems were obtained on the principles of the physics of gas discharge processes. Generalized theoretical provisions of the energy model of processes of the researched type make it possible to form a system of analytical criteria, to develop fundamentally new methods of designing and automated control of technological processes of this group. The main conceptual approaches described above, in comparison with known publications, qualify them as prin are particularly new in world scientific practice. The theoretical provisions developed in the work are intended to be used not only in the practice of applying technological processes of the type under study, but also in the training of specialists when teaching training courses in fundamentally new areas of the theory and practice of gas-discharge processes of metal surface treatment. From the theoretical results obtained in the course of research, completely new, innovative methods and algorithms of process control emerge. Taking into account the multi-sectoral nature of the possible use of the specified modification technology, theoretical studies of the process are especially relevant for many branches of industry in Ukraine. The presence of developments in the chosen direction is aimed at the further growth of the production of high-tech equipment and products in Ukraine. The scientific novelty of the obtained results is as follows: - For the first time, it was proposed to introduce the field concentration criterion, which made it possible to solve the analytical problem of establishing the relationships between the surface geometry and electric field parameters, as well as their influence on the wear resistance of steel surfaces nitrided in a cyclically switched discharge. - For the first time, an analytical expression was obtained for determining the average speed of electrons in a glow discharge; for this, a model of the basic speed of an electron that flew without collisions from the cathode to a certain point of the cathode fall region was used. - The phenomenon-effect of relaxation processes in the near-surface layers of steels nitrided in a cyclically switched discharge was revealed. Relax the structures and stresses formed in the surface layers of these materials under the influence of pressure and temperature in the friction zone. - It was established that the wear resistance of the surfaces of long holes of steel parts, nitrided in a cyclically switched discharge, is increased by almost 2 times, due to the effect of pumping nitrogen ions into the hole and, as a result, the uniform distribution of surface microhardness along the entire length - The methodology of increasing the wear resistance of steels by anhydrous nitriding in a cyclically switched discharge, which is a consequence of changing the ratio of the structural components of the phase composition of the surface modified layer, received further development. - The increase in the wear resistance of steel parts of friction nodes by 1.35...1.75 times by nitriding in a cyclically switched discharge is due to the fact that the periodic change in the polarity of the chamber electrodes contributes to the processes of cleaning the surface from the adsorption layer, which positively affects the nature of the saturation of the surface with nitrogen (the gradient of change microhardness along the depth of the nitrided layer decreases from 1.7 to 3.5 times). Practical significance of the obtained results: - The use of the proposed complex of equipment as a key, during nitriding in a glow discharge with non-stationary power supply, made it possible to implement the entire range of operating currents and voltages, which opens the way to the practical use of non-stationary discharge for modifying the surfaces of metal alloys and increasing their wear resistance. - The study of the wear resistance of samples in the dry friction mode ensures a significantly higher productivity of conducting experiments. Unlike limit friction experiments, dry friction can be applied to different steels, with the same pressure value in the contact zone, which facilitates the comparison of results and contributes to the objectivity of conclusions about the effectiveness of different surface modification processes. According to the results of experimental studies, such a compromise pressure can be 16 MPa. The established effect of relaxation transformations of friction surfaces, which were nitrided in a cyclic-commutated discharge, requires recommending to conduct a study of the wear resistance of such surfaces during one continuous shift to ensure adequacy and comparison of results. - In the case of an armored personnel carrier powered by industrial frequency current, the installation for the implementation of the process becomes cheaper. (patent of Ukraine No. 112983). The developed technology was implemented to strengthen gear brackets, gear bushings, gear shafts, and gear wheels at "MAGMA" LLC, Mariupol, which showed an increase in wear resistance from 1.35 to 1.85 compared to high-frequency current strengthening. - The possibility of switching the form of pulses, changing their polarity led to the development of a number of methods and technologies of nitriding (patents of Ukraine, No. 113576, No. 115969, No. 112984, No. 112613 and No. 111949) aimed at increasing the wear resistance of metal products, namely: transitional bushings with internal and external conical threads; screws of thermoplastic machines; and implemented at LLC "Drilling Equipment Factory", Korosten, at PE "Yurkon", at Khmelnytskyi Maslosyrbaz and "Khmelpivo" association. The results of the theoretical and experimental studies of the work are used in the educational process of the KhNU at the Department of Mechanical Engineering when teaching the disciplines "Progressive strengthening technologies", "Tractors and cars".
Physico-technical processes of processing metal surfaces with the use of electric discharge as an intensifier in a gas medium are among the least energyintensive and universal in terms of purpose and use. However, the lack of general theoretical foundations, which would enable optimization, effective management and design of technological processes, hinders the widespread implementation of BATR processes. The purpose of the research is the development of theoretical and practical foundations of increasing the wear resistance of metals by anhydrous nitriding in a cyclically switched discharge, as well as establishing the basic laws and conditions of nitriding of long holes to ensure their wear resistance. The analysis of sources indicates that all known models of the process are theoretically largely hypothetical, as they are not fully confirmed experimentally. A number of options for the implementation of vacuum-diffusion gas-ischarge technologies cannot be explained at all on the basis of the mentioned models. Analytical apparatus is practically not used in their formation, the need to explain some phenomena that fundamentally affect the acceptability of the theory is ignored, there are no criteria, and hence the methods of managing the process in order to achieve the planned and necessary for operation modification indicators. The presence of a voluminous database of technological data, which does not have a generalizing theory, not only does not contribute to the optimization of the technological process, but on the contrary often leads to the opposite consequences, since data for the same type of conditions often contradict each other. The paper develops the position of the theory of diffusion gas-discharge processes of metal surface modification, which are based on the priority of energy approaches. From such positions, the theoretical foundations of the researched technologies were not considered by any of the previous researchers, but precisely such approaches open completely new possibilities for revealing the subtle mechanism of phenomena that take place during the implementation of processes of this type, and further - the development of practical aspects of the use of technology. The conceptual basis of the theoretical approaches used in the work is the energy model of the group of researched processes, the essence of which is that under certain specific conditions those of the elementary subprocesses are implemented first of all, which are energetically most advantageous and probable in view of the energy levels of the factors that stimulate these subprocesses. To implement these provisions, the formation of energy characteristics of process stimulators, primarily of flow elements that interact with the surface, has been consistently studied. At the same time, the factor of energy impact of flows on the surface is taken as a basis, both in terms of the number and energy levels of particles. It is the combination of these characteristics that is of decisive importance for the formation of the characteristics of the main elementary processes. Significant scientific interest with the prospect of wide practical use is the problem of applying power other than continuous. These issues have also not been studied theoretically by anyone. At the same time, in reality, all processes of vacuumdiffusion gas-discharge modification of the surface of metals take place in nonstationary electric fields, since it is practically impossible to provide power with an absolutely constant current. A change in the characteristics of the field leads to the priority passage of one of several competing sub-processes, which ensure either the formation of diffuses on the surface, or their dispersion, or the diffusion of nitrogen into the depth of the surface layer. It is with the help of the controlled form of the electric field indicators in the discharge chamber that it is possible to neutralize to the required extent the blocking effect of the formation of diffundides on the surface, which will allow not only to increase the efficiency of the modification, but also to provide the necessary final results, including the structure of the surface modified layer. Based on the concept of the energy model, the influence of the shape of the control signal on the efficiency of the modification processes was theoretically substantiated and experimentally verified, since this factor significantly affects the tribological characteristics of nitrided layers. Tribological studies were carried out on the basis of the provisions of physicochemical mechanics of materials developed by G. V. Karpenko, G. O. Preis, A. Evans and K. Preis, F. Hammit, as well as the theory of structural adjustment of surface nitrided layers during friction by B. I. Kostecki and the mechano-chemical model of the friction and wear process by V. V. Sheveli and V. P. Oleksandrenko. As a result of the research, fundamentally new scientific results related to the solution of practical problems were obtained on the principles of the physics of gas discharge processes. Generalized theoretical provisions of the energy model of processes of the researched type make it possible to form a system of analytical criteria, to develop fundamentally new methods of designing and automated control of technological processes of this group. The main conceptual approaches described above, in comparison with known publications, qualify them as prin are particularly new in world scientific practice. The theoretical provisions developed in the work are intended to be used not only in the practice of applying technological processes of the type under study, but also in the training of specialists when teaching training courses in fundamentally new areas of the theory and practice of gas-discharge processes of metal surface treatment. From the theoretical results obtained in the course of research, completely new, innovative methods and algorithms of process control emerge. Taking into account the multi-sectoral nature of the possible use of the specified modification technology, theoretical studies of the process are especially relevant for many branches of industry in Ukraine. The presence of developments in the chosen direction is aimed at the further growth of the production of high-tech equipment and products in Ukraine. The scientific novelty of the obtained results is as follows: - For the first time, it was proposed to introduce the field concentration criterion, which made it possible to solve the analytical problem of establishing the relationships between the surface geometry and electric field parameters, as well as their influence on the wear resistance of steel surfaces nitrided in a cyclically switched discharge. - For the first time, an analytical expression was obtained for determining the average speed of electrons in a glow discharge; for this, a model of the basic speed of an electron that flew without collisions from the cathode to a certain point of the cathode fall region was used. - The phenomenon-effect of relaxation processes in the near-surface layers of steels nitrided in a cyclically switched discharge was revealed. Relax the structures and stresses formed in the surface layers of these materials under the influence of pressure and temperature in the friction zone. - It was established that the wear resistance of the surfaces of long holes of steel parts, nitrided in a cyclically switched discharge, is increased by almost 2 times, due to the effect of pumping nitrogen ions into the hole and, as a result, the uniform distribution of surface microhardness along the entire length - The methodology of increasing the wear resistance of steels by anhydrous nitriding in a cyclically switched discharge, which is a consequence of changing the ratio of the structural components of the phase composition of the surface modified layer, received further development. - The increase in the wear resistance of steel parts of friction nodes by 1.35...1.75 times by nitriding in a cyclically switched discharge is due to the fact that the periodic change in the polarity of the chamber electrodes contributes to the processes of cleaning the surface from the adsorption layer, which positively affects the nature of the saturation of the surface with nitrogen (the gradient of change microhardness along the depth of the nitrided layer decreases from 1.7 to 3.5 times). Practical significance of the obtained results: - The use of the proposed complex of equipment as a key, during nitriding in a glow discharge with non-stationary power supply, made it possible to implement the entire range of operating currents and voltages, which opens the way to the practical use of non-stationary discharge for modifying the surfaces of metal alloys and increasing their wear resistance. - The study of the wear resistance of samples in the dry friction mode ensures a significantly higher productivity of conducting experiments. Unlike limit friction experiments, dry friction can be applied to different steels, with the same pressure value in the contact zone, which facilitates the comparison of results and contributes to the objectivity of conclusions about the effectiveness of different surface modification processes. According to the results of experimental studies, such a compromise pressure can be 16 MPa. The established effect of relaxation transformations of friction surfaces, which were nitrided in a cyclic-commutated discharge, requires recommending to conduct a study of the wear resistance of such surfaces during one continuous shift to ensure adequacy and comparison of results. - In the case of an armored personnel carrier powered by industrial frequency current, the installation for the implementation of the process becomes cheaper. (patent of Ukraine No. 112983). The developed technology was implemented to strengthen gear brackets, gear bushings, gear shafts, and gear wheels at "MAGMA" LLC, Mariupol, which showed an increase in wear resistance from 1.35 to 1.85 compared to high-frequency current strengthening. - The possibility of switching the form of pulses, changing their polarity led to the development of a number of methods and technologies of nitriding (patents of Ukraine, No. 113576, No. 115969, No. 112984, No. 112613 and No. 111949) aimed at increasing the wear resistance of metal products, namely: transitional bushings with internal and external conical threads; screws of thermoplastic machines; and implemented at LLC "Drilling Equipment Factory", Korosten, at PE "Yurkon", at Khmelnytskyi Maslosyrbaz and "Khmelpivo" association. The results of the theoretical and experimental studies of the work are used in the educational process of the KhNU at the Department of Mechanical Engineering when teaching the disciplines "Progressive strengthening technologies", "Tractors and cars".
Опис
Ключові слова
зносостійкість, підвищення трибологічних характеристик, сухе тертя, конструкційні сталі, азотування, циклічнокомутований розряд, математичне моделювання, wear resistance, improvement of tribological characteristics, dry friction, structural steels, nitriding, cyclically switched discharge, mathematical modeling
Бібліографічний опис
Люховець В. В. Зносостійкість конструкційних сталей при азотування в циклічно-комутованому розряді : дис. ... канд. техн. наук : 05.02.04 / В. В. Люховець. - Хмельницький : ХНУ, 2024. - 211с.